Chapter 10
Standard: JT/T 808-2013

Technical Appendix

Table 3 terminal parameters, 202 OBD-II data stream PIDs, driving behavior alert codes, and privileged SMS commands.

Appendix

10.1 List of Figures
#

The following sequence diagrams and frame structure figures are specified in this standard:

Figure #TitlePrimary ChapterDirect Link
Fig. 1Business Flowchart of Terminal RegistrationChapter 4: Business ProcessView Fig. 1 Flowchart
Fig. 2Message Structure (Wire Frame Packet Diagram)Chapter 5: Protocol DetailsView Fig. 2 Structure
Fig. 3Structure Chart of Message Body Attributes FormatChapter 5: Protocol DetailsView Fig. 3 Attributes

10.2 List of Key Protocol Tables
#

Table #TitleDescription & TopicExplorer Link
Table 1Data TypePrimitive data types (BYTE, WORD, DWORD, BCD, STRING)Chapter 5
Table 2Message HeaderStandard 12~16 byte packet header fieldsChapter 5
Table 3Packet Encapsulation ItemLong message sub-packet encapsulation headerChapter 5
Table 4User-Defined Parameter IDsTerminal configuration parameters (0xF000 ~ 0xFFFF)Explore Parameters
Table 6Terminal General ResponseACK result status codes for platform commandsView 0x0001
Table 7Platform General ResponseAcknowledgement format for terminal telemetryView 0x8001
Table 8-9Terminal Registration Request & ResponseHandshake provisioning & base key issuanceView 0x0100
Table 18Location Information ReportingGPS position, speed, direction, status flagsView 0x0200
Table 19Location Alarm Flag Bits32-bit alarm bitmask (SOS, speeding, rollover, fault)Chapter 9
Table 20Location Status Flag Bits32-bit vehicle status flags (ACC, fixed, door, fuel)Chapter 9
Table 25OBD Data Stream IDs (Extensible)Real-time vehicle engine RPM, speed, coolant tempExplore OBD PIDs
Table 28Alarm and Driving Behavior Data IDsRapid acceleration, harsh braking, crash, idlingChapter 9

10.3 Trouble Code Description (DTC Data Format)
#

The terminal supports standard automotive OBD-II and heavy-duty commercial vehicle SAE J1939 diagnostic trouble codes:

10.3.1 SAE J1939 Diagnostic Trouble Code Format (4 Bytes)
#

ByteFieldBitmaskDescription and Requirements
Byte 1SPN [7:0]Bit 7 ~ 0SPN lower 8 significant bits (Bit 7 is MSB)
Byte 2SPN [15:8]Bit 7 ~ 0SPN middle 8 significant bits
Byte 3SPN [18:16]Bit 7 ~ 5SPN upper 3 significant bits
Byte 3FMI [4:0]Bit 4 ~ 0Failure Mode Identifier (5 bits, Bit 4 is MSB)
Byte 4Fault PeriodBit 70: Current active fault; 1: Historical fault
Byte 4Fault CountBit 6 ~ 0Current fault occurrence count (Bit 1 ~ 7)

10.3.2 Standard OBD-II DTC Format (4 Bytes)
#

ByteFieldDescription and Requirements
Byte 1DTC Low ByteStandard OBD-II Diagnostic Trouble Code low byte (e.g. P0300, P0420)
Byte 2DTC High ByteStandard OBD-II Diagnostic Trouble Code high byte
Byte 3ReservedReserved byte, fixed at 0x00
Byte 4Fault PeriodBit 7 indicates fault occurrence period (0: Current active fault, 1: Historical fault)

10.4 Privileged SMS Configuration Commands
#

The terminal should have SMS service enabled on its cellular SIM card to allow emergency configuration and control even if cellular GPRS/LTE data links fail:

ItemFunction NameSMS Command SyntaxTerminal Reply FormatDescription
1Restart TerminalReboot!Reboot OK!Restarts device MCU and cellular modem
2Factory ResetRestore!Restore OK!Resets configuration parameters to factory defaults (server IP & port remain unchanged)
3Query Server AddressPort?query Port:[IP]:[PORT];Inquires currently configured telematics server address & port
4Set Server Address*SETSERVER:[IP],[PORT]#set server success ip=[IP] port=[PORT]Sets server IP address or domain name and port
5Query Registration StatusRegister State?Registered! or Unregister!Checks if device is currently registered on the platform
6Terminal DeregistrationDeregister!Deregister OK!Clears registration ID and deletes base key from FLASH

10.5 Device Self-Check Modules
#

When executing on-demand or periodic hardware self-check diagnostics, the terminal inspects sub-system modules and reports status flags:

Self-Check IDHardware ModuleStatus CodeDiagnostic State & Meaning
0x01GPS / GNSS Module0x00Succeeded / Normal operation
0x01GPS / GNSS Module0x01Antenna disconnected
0x01GPS / GNSS Module0x02Antenna short-circuited
0x02Bluetooth Module0x00Succeeded / Normal operation
0x02Bluetooth Module0x01Failed / No communication
0x03Backup Battery Module0x00Succeeded / Normal voltage
0x03Backup Battery Module0x01Low battery voltage
0x03Backup Battery Module0x02Abnormal battery / Charging fault
0x04CAN Bus Controller0x00Succeeded / Normal CAN bus activity
0x04CAN Bus Controller0x01Failed to connect CAN transceiver
0x05G-Sensor / Gyroscope0x00Succeeded / Accelerometer ready
0x05G-Sensor / Gyroscope0x01Sensor I2C/SPI communication failed
0x06K-Line Interface0x00Succeeded / Normal K-Line transceiver
0x06K-Line Interface0x01K-Line communication failed
0x07FLASH Storage Chip0x00Succeeded / SPI FLASH accessible
0x07FLASH Storage Chip0x01SPI FLASH read/write failed
0x08Vin ADC Sampling0x00Succeeded / Operating voltage normal
0x08Vin ADC Sampling0x01Main voltage ADC sampling abnormal